MIRAN Magnetostrictive Liquid Level Displacement Sensor
MBT series manual
1.Summary In the ferromagnetic material in the direction of magnetization can cause the change of medium lattice spacing change, which makes the ferromagnetic length and volume change, namely: magnetostrictive phenomenon, also known as the Wiedemann effect, the reverse effect is called the Villari effect. The principle of the magnetostrictive sensor is the use of two different magnetic field at the intersection of a strain pulse signal, and then calculate the signal detected by the time period required to calculate the exact location. The two one from the magnetic field of permanent magnet excitation pulse generating another from the sensor electronic warehouse in electronic components. The exciting pulse is made of a magnetostrictive material made of a magnetostrictive material. When the intersection of permanent magnetic field and the magnetic ring, due to the magnetostrictive phenomenon, mechanical vibration generated by the waveguide wire to form a strain pulse. The strain pulse is quickly detected by the sensing circuit in the electronic cabin. From the excitation pulse generated a moment to strain pulse detected by the total time multiplied by the fixed velocity, we can accurately calculate the position change of the magnet. This process is continuous, so when the position of the magnetic loop is changed, the new location will be rapidly measured. The output signal is the absolute value of the real, rather than the proportion or need to signal amplification processing, so there is no signal drift or variable values, not like other sensors that require regular re calibration. Magnetostrictive sensor for non-contact, never wear. Has the advantages of high resolution, high precision, high stability, high reliability, fast response time, long service life etc.. Sensors do not have to be re calibrated, do not have regular maintenance.
2.Technical Parameter
| Stroke Range |
30~5000mm |
| Power Supply |
+24VDC |
| Output signal |
0-20mADC,4-20mADC,0-5VDC,1-5VDC,0-10VDC Digital signal: RS485 Agreement: MODBUS,FRDGL |
| On site display: |
current level and liquid temperature |
| Touch button |
press a button LED display 2 minutes, press the button to close the LED display |
| Load capacity |
Voltage signal output load≥4KΩ Current signal output load≤500Ω |
| Nonlinear error |
+ 0.05%FS; 200mm maximum error below 100μm |
| Repeatability error |
better than 0.005%FS |
| Resolution |
better than 0.005%FS |
| Hysteresis |
better than 0.002%FS |
| working temperature |
0-+70ºC -15-+60ºC -25-+70ºC -40-+85ºC |
| Rod material |
0Cr18Ni9 (304) of 316 stainless steel (customized) |
| Lead |
PVC shield cable (the default length: 1m, can also be provided according to user requirements) |
| Shell protection class |
IP67 |
3.Installation Dimension
3.1 Precautions before installation Read all the installation instructions carefully and prevent the installation of environmental temperature, shock, vibration, pressure and size exceeds the allowable range of the sensor; don't make the rod bending; do not make the electronic components of the sensor end or the end to bear large impact; users deal with the use of environmental products, anti-corrosion, explosion-proof and function selection responsible for sensor special requirements can not be used for chemical reaction or other damage to the sensor inflammable explosive corrosive vapor and liquid etc.; installed, with protective treatment instrument.
3.2 Installation Method
3.2.1 Installation method
3.2.2 Installation diagram
Electrical Installation
4.Sensor wiring precautions
4.1.1Shield cable sensor must avoid the power supply, the RF signal source and other noise transmission lines.
4.1.2 Users in the terminal before, please check whether the power supply to meet the +24VDC requirements, and the output of the power supply must be greater than the total power consumption of products, calculation of each sensor according to the different range of less than 95mA. If the power supply does not meet the requirements, replace the power supply to ensure that the sensor can work properly.
4.2 Analog signal output connection:
4.2.1 Waterproof joint straight outlet wiring: The sensor consists of five points: the power is (brown), negative power (black), the output signal is output signal (blue) and negative (white), shell (shield).
4.2.2 Air plug connection mode: The sensor consists of five points: 1. The power is (brown), power (black), the negative output signal is the output signal (blue) and negative (white), shell (shield) Specific wiring as shown in figure:
4.2.3 Hessman plug connection mode: The sensor consists of four points: 1. The positive supply (brown), the output signal is (blue), the negative power supply signal of the negative (black and white) E, shell (shield) 4. 3 Digital signal output connection: 4.3.1 Waterproof joint straight outlet wiring: The sensor consists of five contacts: positive supply (brown), power (black), RS485A (blue), RS485B (white), shell (shield). 4.3.2 Air plug connection mode: The sensor consists of five points: 1. The positive supply (brown), the power (black), RS485A (blue), the RS485B (white), shell (shield) 4. 3. 3 Hessman plug connection mode: The sensor consists of four points: 1. The positive supply (brown), the RS485A (blue), RS485B (white) E, negative power (black)
5. Adjustment
The sensor in the factory has been in accordance with the full range of zero and full adjustment. Due to the long-term stability of the sensor is very good, do not need to adjust the whole use cycle. Thus, in order to improve the reliability, the sensor does not leave a port for adjustment. Please select the parameter calibration of the two meter measurement. If the user needs to reset the zero and full, please contact our company.
Company Information
Miran Industry Zone
Marketing Team
Show Room
Certificate Room
My Dear Friends,welcome to visit our company!
Shenzhen Miran Technology Co., Ltd. is the largest Linear Position Sensor manufacturer in China.
Since 2003 we have been developed and produced Linear Position Sensor(brand:MIRAN,LinecSKI,WANSUNGM),Wire Rope Potentiometer,Magnetostrictive Liquid Level Sensor,Angle Sensor,Lubricating Pump(Oil/Grease/Butter),LVDT,Eddy Current Sensor, and many other Motion control products to support many different industries.
Our Products have been widely used in injection molding machines,die casting machines,rubber machines,footwear machines,EVA injection machines,bottle blowing machines,woodworker machines, hydraulic machinery,level control, suspension stroke control,construciton machinery,seaport machinery,industrial robots,etc.
We can offer you the competitive advantage products.
We also support to put your logo on the products if you need.
Please find the product you need and confirm the order.
If you cannot find what you need,please leave a message with your email or
Hope we can build up the long-term and harmonious business relationship!
Wish you have a happy shopping and visit us again!
miranyuki.en.made-in-china.com
Audited Supplier 
){kind=link}